Lincoln Timer to Generate a PWM
From Manuals
(Difference between revisions)
(→Compatibility Lincoln 60, Lincoln 60E) |
|||
| (3 intermediate revisions not shown) | |||
| Line 1: | Line 1: | ||
==Compatibility [http://www.micromint.com/index.php/SBC/lincoln60.html Lincoln 60], [http://www.micromint.com/index.php/SBC/lincoln60.html Lincoln 60E]== | ==Compatibility [http://www.micromint.com/index.php/SBC/lincoln60.html Lincoln 60], [http://www.micromint.com/index.php/SBC/lincoln60.html Lincoln 60E]== | ||
| - | This example demonstrates how to use timers to generate PWM signals with different duty cycles. Run the example and observe the 4 signals using an oscilloscope. | + | This example demonstrates how to use timers to generate PWM signals with different duty cycles. Run the example and observe the 4 signals using an oscilloscope. Below is a list of the signals and what duty cycle they should be at: |
| - | + | ||
| - | + | * P1.28 on J2 pin 19: duty cycle = 12.5% | |
| - | + | * P1.22 on J2 pin 13: duty cycle = 25% | |
| - | + | * P0.6 on J2 pin 5: duty cycle = 37.5% | |
| - | + | * P0.10 on J2 pin 9: duty cycle = 50% | |
| - | + | ||
| + | The first UART, which is connected to the COM1 on the Lincoln microcontroller board, is configured for 115,200 bits per second, and 8-n-1 mode. When the program is started a message will be printed to the terminal. The below screen shot is of the timer_pwmsignal in action. | ||
[[Image:Lincoln_timer_pwmsignal.png|center|]] | [[Image:Lincoln_timer_pwmsignal.png|center|]] | ||
| + | |||
| + | |||
| + | Below is a screen capture of the signals on P1.28 (J2 pin 19) and P1.22 (J2 pin 13). | ||
| + | |||
[[Image:Lincoln_timer_pwmsignal1.png|center|]] | [[Image:Lincoln_timer_pwmsignal1.png|center|]] | ||
| + | |||
| + | |||
| + | Below is a screen capture of the signals on P0.6 (J2 pin 5) and P0.10 (J2 pin 9). | ||
| + | |||
[[Image:Lincoln_timer_pwmsignal2.png|center|]] | [[Image:Lincoln_timer_pwmsignal2.png|center|]] | ||
Current revision as of 20:16, 12 April 2012
Compatibility Lincoln 60, Lincoln 60E
This example demonstrates how to use timers to generate PWM signals with different duty cycles. Run the example and observe the 4 signals using an oscilloscope. Below is a list of the signals and what duty cycle they should be at:
- P1.28 on J2 pin 19: duty cycle = 12.5%
- P1.22 on J2 pin 13: duty cycle = 25%
- P0.6 on J2 pin 5: duty cycle = 37.5%
- P0.10 on J2 pin 9: duty cycle = 50%
The first UART, which is connected to the COM1 on the Lincoln microcontroller board, is configured for 115,200 bits per second, and 8-n-1 mode. When the program is started a message will be printed to the terminal. The below screen shot is of the timer_pwmsignal in action.
Below is a screen capture of the signals on P1.28 (J2 pin 19) and P1.22 (J2 pin 13).
Below is a screen capture of the signals on P0.6 (J2 pin 5) and P0.10 (J2 pin 9).
