Bambino-210 Manual/Appendix B
From Manuals
(Difference between revisions)
(→Appendix B - Using an External JTAG with the BAM210) |
|||
| Line 4: | Line 4: | ||
* 2. Boot the MBED HDK into CRP DISABLED mode by shorting JP3 while connecting the USB Cable to USB1. A [[Image:CRP_DISABLED.png]] drive should appear. [[Image:BAM210E_CRP_DISABLED.png|center]] | * 2. Boot the MBED HDK into CRP DISABLED mode by shorting JP3 while connecting the USB Cable to USB1. A [[Image:CRP_DISABLED.png]] drive should appear. [[Image:BAM210E_CRP_DISABLED.png|center]] | ||
* 3. Program the Interface firmware by deleting the firmware.bin file and copy lpc11u35_vcom.bin to the CRP DISABLED disk. | * 3. Program the Interface firmware by deleting the firmware.bin file and copy lpc11u35_vcom.bin to the CRP DISABLED disk. | ||
| - | * 4. Reboot the Interface by disconnecting and reconnecting the | + | * 4. Reboot the Interface by disconnecting and reconnecting the USB1 cable without JP3 shorted |
* 5. Finished! | * 5. Finished! | ||
The JTAG connector now free to use with an external JTAG. A virtual COM port is now available on USB1. | The JTAG connector now free to use with an external JTAG. A virtual COM port is now available on USB1. | ||
| + | The signals used for the virtual COM port are listed below: | ||
| + | {| border="1" cellpadding="5" cellspacing="2" align="center" style="text-align: center;" | ||
| + | |+ align="bottom"|'''Signals Used and Connector Locations for Example 05-04''' | ||
| + | |'''Signal''' | ||
| + | |'''LPC4330 PIN NAME''' | ||
| + | |'''BAM210E''' | ||
| + | |'''BAM210''' | ||
| + | |'''BAM200E''' | ||
| + | |'''BAM200''' | ||
| + | |'''Used for''' | ||
| + | |- | ||
| + | |USBTX | ||
| + | |P2_10 | ||
| + | |MBED-HDK | ||
| + | |MBED-HDK | ||
| + | |S10-4 | ||
| + | |n/p | ||
| + | |MBED-HDK Serial RX | ||
| + | |- | ||
| + | |USBRX | ||
| + | |P2_11 | ||
| + | |MBED-HDK | ||
| + | |MBED-HDK | ||
| + | |s10-5 | ||
| + | |n/p | ||
| + | |MBED-HDK Serial TX | ||
| + | |- | ||
| + | |} | ||
---- | ---- | ||
[[Bambino-210_Manual/Appendix A|PREVIOUS: Appendix A]] | [[Bambino-210_Manual/Appendix A|PREVIOUS: Appendix A]] | ||
Revision as of 12:54, 7 October 2014
Appendix B - Using an External JTAG with the BAM210
- 1. Locate the LPC11U35 Virtual COM Port Binary
- 2. Boot the MBED HDK into CRP DISABLED mode by shorting JP3 while connecting the USB Cable to USB1. A
drive should appear. 
- 3. Program the Interface firmware by deleting the firmware.bin file and copy lpc11u35_vcom.bin to the CRP DISABLED disk.
- 4. Reboot the Interface by disconnecting and reconnecting the USB1 cable without JP3 shorted
- 5. Finished!
The JTAG connector now free to use with an external JTAG. A virtual COM port is now available on USB1. The signals used for the virtual COM port are listed below:
| Signal | LPC4330 PIN NAME | BAM210E | BAM210 | BAM200E | BAM200 | Used for |
| USBTX | P2_10 | MBED-HDK | MBED-HDK | S10-4 | n/p | MBED-HDK Serial RX |
| USBRX | P2_11 | MBED-HDK | MBED-HDK | s10-5 | n/p | MBED-HDK Serial TX |