Eagle-50 Manual/Getting Started - Revision history

Support: /* Downloading Code Examples using the LM Flash Programmer and the optional onboard USB Debugger */

Support — Thu, 05 Apr 2012 15:30:33 GMT

Downloading Code Examples using the LM Flash Programmer and the optional onboard USB Debugger

← Older revision		Revision as of 15:30, 5 April 2012
Line 80:		Line 80:

	===Downloading Code Examples using the LM Flash Programmer and the optional onboard USB Debugger===		===Downloading Code Examples using the LM Flash Programmer and the optional onboard USB Debugger===
-	The USB Debugger option for the Eagle 50 and Eagle 50E can be used with the LM Flash Programmer software to program the board. The Eagle 50 and Eagle 50E come preprogrammed with a bootloader that uses the first 8 KB of the flash address space (0x00000000 to 0x00001fff). If you wish to keep the bootloader then applications should be linked to start at address 0x00002000.	+	The USB Debugger option for the Eagle 50 and Eagle 50E can be used with the LM Flash Programmer software to program the board. The LM Flash Programmer can be downloaded from Texas Instruments website http://www.ti.com/tool/lmflashprogrammer. The Eagle 50 and Eagle 50E come preprogrammed with a bootloader that uses the first 8 KB of the flash address space (0x00000000 to 0x00001fff). If you wish to keep the bootloader then applications should be linked to start at address 0x00002000.

	Follow these steps to download Code Examples using the LM Flash Programmer and keeping the bootloader entact:		Follow these steps to download Code Examples using the LM Flash Programmer and keeping the bootloader entact:

Support: /* Downloading Code Examples using the LM Flash Programmer and the optional onboard USB Debugger */

Support — Tue, 03 Apr 2012 19:29:23 GMT

Downloading Code Examples using the LM Flash Programmer and the optional onboard USB Debugger

← Older revision		Revision as of 19:29, 3 April 2012
Line 80:		Line 80:

	===Downloading Code Examples using the LM Flash Programmer and the optional onboard USB Debugger===		===Downloading Code Examples using the LM Flash Programmer and the optional onboard USB Debugger===
-	The USB Debugger option for the Eagle 50 and Eagle 50E can be used with the LM Flash Programmer software to program the board. ~~To load~~ the flash ~~programmer, select Programs> Micromint Eagle>~~ LM Flash Programmer> LM Flash Programmer from ~~your Windows Start menu~~. Go to the “Setup” tab to see a screen similar to that in Figure 2.7. On “Interface” select “ICDI (Eval Board)”.	+	The USB Debugger option for the Eagle 50 and Eagle 50E can be used with the LM Flash Programmer software to program the board. The Eagle 50 and Eagle 50E come preprogrammed with a bootloader that uses the first 8 KB of the flash address space (0x00000000 to 0x00001fff). If you wish to keep the bootloader then applications should be linked to start at address 0x00002000.
-	~~The bootloader uses~~ the ~~first~~ 8 ~~KB of~~ the ~~flash address space~~ (~~0x00000000 to 0x00001fff~~). ~~If you wish~~ to ~~keep~~ the bootloader ~~then applications should~~ be linked to start at address ~~0x00002000~~. ~~That is done automatically if you use~~ the ~~“ewarm/application~~.~~icf” or “gcc/application~~.~~ld” linker scripts used in~~ the ~~examples~~. ~~The application should then be downloaded by setting up~~ the ~~LM Flash Programmers~~ “Program” tab like Figure 2.8. ~~You can overwrite~~ the ~~bootloader if you so desire~~ by ~~using~~ the ~~ewarm/standalone~~.~~icf” or “gcc/ standalone~~.~~ld” linker scripts and downloading your binary image at address 0x0~~.	+
		+	Follow these steps to download Code Examples using the LM Flash Programmer and keeping the bootloader entact:
		+	* 1. If the LM Flash Programmer is not installed it can be downloaded from Texas Instruments Website.
		+	* 2. Besure that the Code Example is linked to start at address 0x2000.
		+	* 3. Open the LM Flash Programmer.
		+	* 4. Go to the “Setup” tab to see a screen similar to that in Figure 2.7.
		+	* 5. On “Interface” select “ICDI (Eval Board)”.
		+	* 6. Go to the “Program” tab like Figure 2.8.
		+	* 7. Browse for the Code Examples binary file by clicking on the "Browse" button.
		+	* 8. Under "Options" select "Erase Necessary Pages - (slower)".
		+	* 9. In "Program Address Offset:" enter 2000.
		+	* 10. Click the "Program" button.
		+
		+	Follow these steps to download Code Examples using the LM Flash Programmer without the bootloader:
		+	* 1. If the LM Flash Programmer is not installed it can be downloaded from Texas Instruments Website.
		+	* 2. Besure that the Code Example is linked to start at address 0x0.
		+	* 3. Open the LM Flash Programmer.
		+	* 4. Go to the “Setup” tab to see a screen similar to that in Figure 2.7.
		+	* 5. On “Interface” select “ICDI (Eval Board)”.
		+	* 6. Go to the “Program” tab like Figure 2.8.
		+	* 7. Browse for the Code Examples binary file by clicking on the "Browse" button.
		+	* 8. Under "Options" select "Erase Entire Flash - (faster)".
		+	* 9. In "Program Address Offset:" enter 0.
		+	* 10. Click the "Program" button.

	[[Image:USB_Configuration.png\|center\|frame\|alt=USB flash configuration\|Figure 2.7: USB debug port flash programmer configuration]]		[[Image:USB_Configuration.png\|center\|frame\|alt=USB flash configuration\|Figure 2.7: USB debug port flash programmer configuration]]

Support: /* Steps to Getting Started */

Support — Tue, 03 Apr 2012 19:11:31 GMT

Steps to Getting Started

← Older revision		Revision as of 19:11, 3 April 2012
Line 9:		Line 9:
	* 4. [http://wiki.micromint.com/index.php/Eagle-50_Manual/Getting_Started#Install_the_Chosen_Compiler_and_IDE Install the Chosen Compiler and IDE]		* 4. [http://wiki.micromint.com/index.php/Eagle-50_Manual/Getting_Started#Install_the_Chosen_Compiler_and_IDE Install the Chosen Compiler and IDE]
	* 5. [http://wiki.micromint.com/index.php/Eagle-50_Manual/Getting_Started#Compile_a_Code_Example Compile a Code Example ]		* 5. [http://wiki.micromint.com/index.php/Eagle-50_Manual/Getting_Started#Compile_a_Code_Example Compile a Code Example ]
-	* 6. [http://wiki.micromint.com/index.php/Eagle-50_Manual/Getting_Started#~~Download_the_Code_Example_to_the_Eagle_50~~.2F50E Downloading Code Example to the Eagle 50/50E]	+	* 6. [http://wiki.micromint.com/index.php/Eagle-50_Manual/Getting_Started#Downloading_Code_Examples_to_the_Eagle_50.2F50E Downloading Code Example to the Eagle 50/50E]

	==Run the Preloaded Application==		==Run the Preloaded Application==

Support: /* Steps to Getting Started */

Support — Tue, 03 Apr 2012 19:10:35 GMT

Steps to Getting Started

← Older revision		Revision as of 19:10, 3 April 2012
Line 9:		Line 9:
	* 4. [http://wiki.micromint.com/index.php/Eagle-50_Manual/Getting_Started#Install_the_Chosen_Compiler_and_IDE Install the Chosen Compiler and IDE]		* 4. [http://wiki.micromint.com/index.php/Eagle-50_Manual/Getting_Started#Install_the_Chosen_Compiler_and_IDE Install the Chosen Compiler and IDE]
	* 5. [http://wiki.micromint.com/index.php/Eagle-50_Manual/Getting_Started#Compile_a_Code_Example Compile a Code Example ]		* 5. [http://wiki.micromint.com/index.php/Eagle-50_Manual/Getting_Started#Compile_a_Code_Example Compile a Code Example ]
-	* 6. [http://wiki.micromint.com/index.php/Eagle-50_Manual/Getting_Started#Download_the_Code_Example_to_the_Eagle_50.2F50E ~~Download the~~ Code Example to the Eagle 50/50E]	+	* 6. [http://wiki.micromint.com/index.php/Eagle-50_Manual/Getting_Started#Download_the_Code_Example_to_the_Eagle_50.2F50E Downloading Code Example to the Eagle 50/50E]

	==Run the Preloaded Application==		==Run the Preloaded Application==

Support: /* Download the Code Example to the Eagle 50/50E */

Support — Tue, 03 Apr 2012 19:06:37 GMT

Download the Code Example to the Eagle 50/50E

← Older revision		Revision as of 19:06, 3 April 2012
Line 74:		Line 74:
	{{:Compile Code Examples Eagle SBC}}		{{:Compile Code Examples Eagle SBC}}

-	==~~Download the~~ Code ~~Example~~ to the Eagle 50/50E==	+	==Downloading Code Examples to the Eagle 50/50E==
	There are many options to download firmware to the Eagle SBC. This section covers firmware downloads using a J-Link debugger, USB Debugger, Ethernet Bootloader, and Serial Bootloader. The method used to download firmware will depend on what hardware is being used.		There are many options to download firmware to the Eagle SBC. This section covers firmware downloads using a J-Link debugger, USB Debugger, Ethernet Bootloader, and Serial Bootloader. The method used to download firmware will depend on what hardware is being used.

	{{:Download Code Example Eagle SBC}}		{{:Download Code Example Eagle SBC}}

-	===Downloading ~~Firmware~~ using the LM Flash Programmer and the optional onboard USB Debugger===	+	===Downloading Code Examples using the LM Flash Programmer and the optional onboard USB Debugger===
	The USB Debugger option for the Eagle 50 and Eagle 50E can be used with the LM Flash Programmer software to program the board. To load the flash programmer, select Programs> Micromint Eagle> LM Flash Programmer> LM Flash Programmer from your Windows Start menu. Go to the “Setup” tab to see a screen similar to that in Figure 2.7. On “Interface” select “ICDI (Eval Board)”.		The USB Debugger option for the Eagle 50 and Eagle 50E can be used with the LM Flash Programmer software to program the board. To load the flash programmer, select Programs> Micromint Eagle> LM Flash Programmer> LM Flash Programmer from your Windows Start menu. Go to the “Setup” tab to see a screen similar to that in Figure 2.7. On “Interface” select “ICDI (Eval Board)”.
	The bootloader uses the first 8 KB of the flash address space (0x00000000 to 0x00001fff). If you wish to keep the bootloader then applications should be linked to start at address 0x00002000. That is done automatically if you use the “ewarm/application.icf” or “gcc/application.ld” linker scripts used in the examples. The application should then be downloaded by setting up the LM Flash Programmers “Program” tab like Figure 2.8. You can overwrite the bootloader if you so desire by using the ewarm/standalone.icf” or “gcc/ standalone.ld” linker scripts and downloading your binary image at address 0x0.		The bootloader uses the first 8 KB of the flash address space (0x00000000 to 0x00001fff). If you wish to keep the bootloader then applications should be linked to start at address 0x00002000. That is done automatically if you use the “ewarm/application.icf” or “gcc/application.ld” linker scripts used in the examples. The application should then be downloaded by setting up the LM Flash Programmers “Program” tab like Figure 2.8. You can overwrite the bootloader if you so desire by using the ewarm/standalone.icf” or “gcc/ standalone.ld” linker scripts and downloading your binary image at address 0x0.

Support at 13:25, 3 April 2012

Support — Tue, 03 Apr 2012 13:25:10 GMT

← Older revision		Revision as of 13:25, 3 April 2012
Line 70:		Line 70:

	{{:Cortex M3 Compiler Installation}}		{{:Cortex M3 Compiler Installation}}
-
-	* [http://www.eclipse.org/cdt/downloads.php Eclipse CDT Updates]
-	* [http://sourceforge.net/apps/mediawiki/gnuarmeclipse/index.php?title=Main_Page GNU ARM Eclipse Plug-in]
-	* [http://www.codeblocks.org/downloads CodeBlocks Updates]

	==Compile a Code Example==		==Compile a Code Example==

Support: /* Download the Code Example to the Eagle 50/50E */

Support — Tue, 27 Mar 2012 13:39:10 GMT

Download the Code Example to the Eagle 50/50E

← Older revision		Revision as of 13:39, 27 March 2012
Line 82:		Line 82:

	{{:Download Code Example Eagle SBC}}		{{:Download Code Example Eagle SBC}}
		+
		+	===Downloading Firmware using the LM Flash Programmer and the optional onboard USB Debugger===
		+	The USB Debugger option for the Eagle 50 and Eagle 50E can be used with the LM Flash Programmer software to program the board. To load the flash programmer, select Programs> Micromint Eagle> LM Flash Programmer> LM Flash Programmer from your Windows Start menu. Go to the “Setup” tab to see a screen similar to that in Figure 2.7. On “Interface” select “ICDI (Eval Board)”.
		+	The bootloader uses the first 8 KB of the flash address space (0x00000000 to 0x00001fff). If you wish to keep the bootloader then applications should be linked to start at address 0x00002000. That is done automatically if you use the “ewarm/application.icf” or “gcc/application.ld” linker scripts used in the examples. The application should then be downloaded by setting up the LM Flash Programmers “Program” tab like Figure 2.8. You can overwrite the bootloader if you so desire by using the ewarm/standalone.icf” or “gcc/ standalone.ld” linker scripts and downloading your binary image at address 0x0.
		+
		+	[[Image:USB_Configuration.png\|center\|frame\|alt=USB flash configuration\|Figure 2.7: USB debug port flash programmer configuration]]
		+
		+	[[Image:USB_Download.png\|center\|frame\|alt=USB download\|Figure 2.8: USB debug port flash programmer download]]

	==Optional USB Debug Port Unlock Procedure==		==Optional USB Debug Port Unlock Procedure==

Support at 13:37, 27 March 2012

Support — Tue, 27 Mar 2012 13:37:07 GMT

← Older revision		Revision as of 13:37, 27 March 2012
Line 80:		Line 80:
	==Download the Code Example to the Eagle 50/50E==		==Download the Code Example to the Eagle 50/50E==
	There are many options to download firmware to the Eagle SBC. This section covers firmware downloads using a J-Link debugger, USB Debugger, Ethernet Bootloader, and Serial Bootloader. The method used to download firmware will depend on what hardware is being used.		There are many options to download firmware to the Eagle SBC. This section covers firmware downloads using a J-Link debugger, USB Debugger, Ethernet Bootloader, and Serial Bootloader. The method used to download firmware will depend on what hardware is being used.
-	~~===Downloading Firmware using EWARM===~~
-	To use the J-Link debugger with IAR EWARM, select Projects> Options> Debugger with the project name selected in the workspace. On the “Setup” tab select “J-Link/J-Trace” as the driver and “main” as the location to run to. On the Download tab make sure that “Use flash loader(s) is checked. Click OK to save the settings. Then select the “Download and debug” button on the toolbar and then the “Go” button to execute.
-	To use the USB debugger with IAR EWARM, select Projects> Options> Debugger with the project name selected in the workspace. On the “Setup” tab select “LMI FTDI” as the driver and “main” as the location to run to. On the Download tab make sure that “Use flash loader(s)” is checked. Click OK to save the settings. Then select the “Download and debug” button on the toolbar and then the “Go” button to execute.
-	~~===Downloading Firmware using the LM Flash Programmer and the optional onboard USB Debugger===~~
-	The USB Debugger option for the Eagle 50 and Eagle 50E can be used with the LM Flash Programmer software to program the board. To load the flash programmer, select Programs> Micromint Eagle> LM Flash Programmer> LM Flash Programmer from your Windows Start menu. Go to the “Setup” tab to see a screen similar to that in Figure 2.7. On “Interface” select “ICDI (Eval Board)”.
-	The bootloader uses the first 8 KB of the flash address space (0x00000000 to 0x00001fff). If you wish to keep the bootloader then applications should be linked to start at address 0x00002000. That is done automatically if you use the “ewarm/application.icf” or “gcc/application.ld” linker scripts used in the examples. The application should then be downloaded by setting up the LM Flash Programmers “Program” tab like Figure 2.8. You can overwrite the bootloader if you so desire by using the ewarm/standalone.icf” or “gcc/ standalone.ld” linker scripts and downloading your binary image at address 0x0.
-
-	~~[[Image:USB_Configuration.png\|center\|frame\|alt=USB flash configuration\|Figure 2.7: USB debug port flash programmer configuration]]~~
-
-	~~[[Image:USB_Download.png\|center\|frame\|alt=USB download\|Figure 2.8: USB debug port flash programmer download]]~~

-	~~===Downloading Firmware using the CoFlash Flash Programmer and the picoJTAG===~~	+	{{:Download Code Example Eagle SBC}}
-		+
-	~~===Downloading Firmware using the Ethernet Bootloader===~~	+
-	The Eagle 50E is shipped with an Ethernet bootloader that can be used to update the firmware on the board from an Ethernet connection. The bootloader uses the BOOTP and TFTP protocols to temporarily acquire an IP address and copy the binary image to the board. The LM Flash Programmer implements a small BOOTP and TFTP server to do this.	+
-		+
-	The bootloader uses the first 8 KB of the flash address space (0x00000000 to 0x00001fff). Programs loaded with the bootloader should be linked to start at address 0x00002000. That is done automatically if you use the “ewarm/application.icf” or “gcc/application.ld” linker scripts used in the examples.	+
-		+
-	You can overwrite the bootloader if you so desire by using the “ewarm/standalone.icf” or “gcc/ standalone.ld” linker scripts and downloading your binary image via the JTAG. Currently the bootloader cannot be overwritten via the Ethernet port.	+
-		+
-	~~Follow the below steps to use the LM Flash Programmer and the Ethernet bootloader~~:	+
-	*1. Connect the Eagle 50E’s Ethernet port to the network.	+
-	*2. Apply power to the Eagle 50E.	+
-	*3. Press and hold the Eagle 50E’s “USER” button.	+
-	*4. Press and release the Eagle 50E’s “RESET” button.	+
-	*5. Release the “USER” button. The Eagle 50E’s “USER LED” should now be blinking approximately once a second.	+
-	*6. Open the LM Flash Programmer	+
-	*7. Select the "Setup" tab and you will see a screen similar to Figure 2.9	+
-	*8. For "Interface" select "Ethernet"	+
-	*9. For "Ethernet Adapter:" select the adapter that is connected to the computers network.	+
-	*10. For “Client IP Address:” enter an IP address that is on the same subnet as your Ethernet adapter. The last octet must be different than the Ethernet Adapters.	+
-	*11. For “Client MAC Address:” enter the Eagle 50E’s serial number. It can be found on the bottom of the board and should start with 0021A3. Make sure to separate the octets with dashes (00-21-A3).	+
-	*12. Select the "Program" tab on the LM Flash Programmer software and you will see a screen similar to Figure 2.10.	+
-	*13. Click the “Browse” button and locate the application to be downloaded.	+
-	*14. Click on the “Program” button. It generally takes several seconds for the program to start downloading.	+
-		+
-	~~[[Image:Ethernet_configuration.png\|center\|frame\|alt=Ethernet configuration\|Figure 2.9: Ethernet Bootloader Flash programmer configuration]]~~	+
-		+
-	~~[[Image:Ethernet_download.png\|center\|frame\|alt=Ethernet download\|Figure 2.10: Ethernet Bootloader flash programmer download]]~~	+
-		+
-	~~Ethernet bootloader troubleshooting guide:~~	+
-	*1. Temporarily turn off the computers firewall. If this works add the LM Flash programmer to the Firewalls Exceptions list.	+
-	*2. Try bypassing the network by connecting the Eagle 50E directly to the computer Ethernet port. A regular CAT5 cable will work. Make sure to close the LM Flash Programmer software and start at step 2 in the above procedure.	+
-		+
-	~~===Downloading Firmware using the Serial Bootloader===~~	+
-	The Eagle 50 is shipped with a Serial bootloader that can be used to update the firmware on the board from a Serial connection. To place the bootloader in update mode you need to press and hold the user button while the board is starting up, e.g. via power up or when pressing the reset button. After the board starts up release the user button and you will see the user LED blinking approximately once per second. That indicates the board is ready to receive a firmware update via a Serial connection.	+
-		+
-	Programs loaded with the bootloader should be linked to start at address 0x00002000. That is done automatically if you use the “ewarm/application.icf” or “gcc/application.ld” linker scripts used in the examples. You can overwrite the bootloader if you so desire by using the “ewarm/standalone.icf” or “gcc/ standalone.ld” linker scripts and downloading your binary image via the JTAG. Currently the bootloader cannot be overwritten via the Serial port.	+
-		+
-	~~Follow the below steps to set up the LM Flash Loader:~~	+
-	*1. Open the LM Flash Programmer	+
-	*2. Select the "Setup" tab and you will see a screen similar to Figure 2.11	+
-	*3. For "Interface" select "Serial Interface"	+
-	*4. For "COM Port:" select the COM port that is assigned to "Stellaris Virtual COM Port" in the "Device Manager" for the Optioanl USB Debugger or the COM port that you will be using	+
-	*5. The baudrate should be set to 115200	+
-	*6. Set the transfer size to 76	+
-	*7. Select the "Program" tab and you will see a screen similar to Figure 2.12	+
-	*8. Set the "Program Address Offset" to 2000	+
-	*9. Click the "Browse" button and locate the application to be downloaded	+
-		+
-	~~[[Image:Serial_configuration.png\|center\|frame\|alt=Serial configuration\|Figure 2.11: Serial bootloader flash programmer configuration]]~~	+
-		+
-	~~[[Image:Serial_download.png\|center\|frame\|alt=Serial download\|Figure 2.12: Serial bootloader flash programmer download]]~~	+
-		+
-	~~The application can be downloaded using the LM Flash Programmer and the optional USB Debugger by following these steps:~~	+
-	*1. If you are powering the board via USB put a jumper on JP1	+
-	*2. Make sure there is a jumper on JP6	+
-	*3. Connect the USB cable to the computer and the board	+
-	*4. Press and hold the "USER" pushbutton on the board	+
-	*5. Press and release the "RESET" pushbutton on the board and the LED should start blinking around once a second	+
-	*6. Release the "USER" pushbutton	+
-	*7. Click on the "Program" button	+
-		+
-	~~The application can be downloaded using the LM Flash Programmer and COM1 by following these steps:~~	+
-	*1. If you have an optional USB debugger make sure there is NOT a jumper on JP6	+
-	*2. Connect the serial cable to COM1 (J3)	+
-	*3. Power the board	+
-	*4. Press and hold the "USER" pushbutton on the board	+
-	*5. Press and release the "RESET" pushbutton on the board and the LED should start blinking around once a second	+
-	*6. Release the "USER" pushbutton	+
-	*7. Click on the "Program" button	+
-		+
-	~~===Downloading Firmware from the Command Line===~~	+
-	The TI Flash Programmer can also be invoked from the command line. The command line allows you to program the Eagle SBC though Ethernet Bootloader, Serial Bootloader, or FTDI JTAG. This section provides a step by step procedure for each programming method.	+
-	~~Follow these steps to program the board using the command line and the Ethernet Bootloader. The Eagle 50E and Eagle 100 comes with the Ethernet Bootloader.~~	+
-	* 1. Put the board in bootload mode by hold the user pushbutton while pressing and releasing the reset pushbutton. The user LED will blink when it is in bootload mode.	+
-	* 2. Enter the following command line example with your own parameters. Where 192.168.1.201 is the IP address of the computers Ethernet Port and 192.168.1.210 is a free IP address of the network the Eagle SBC is on. 00-21-A3-00-01-02 is the MAC address of the Eagle SBC. The MAC address is also the board’s serial number which is on the bottom of the board.	+
-	~~lmflash -i ethernet -n 192.168.1.201,192.168.1.210,00-21-A3-00-01-02 blinky.bin~~	+
-	* 3. The command line will give you status while the board is programming.	+
-		+
-	~~Follow these steps to program the board using the command line and the Serial Bootloader. The Eagle 50 comes with the Ethernet Bootloader.~~	+
-	* 1. Put the board in bootload mode by hold the user pushbutton while pressing and releasing the reset pushbutton. The user LED will blink when it is in bootload mode.	+
-	* 2. Enter the following command line example with your own parameters. Where COM7 is the COM port that is connected to the Eagle 50 SBC	+
-	~~lmflash -i serial -d -p COM7 -b 115200 -o 0x2000 -r blinky.bin~~	+
-	* 3. The command line will give you status while the board is programming.	+
-		+
-	~~Follow these steps to program the board using the command line and the USB Debug Port~~	+
-	* 1. Connect the USB Debug Port to the computers USB port.	+
-	* 2. Enter the following command line example with your own parameters	+
-		+
-	~~lmflash –I ftdi –r –o 0x2000 blinky.bin~~	+
-	~~3. The command line will give you status while the board is programming.~~	+
-		+
-	~~To see all options available from the command line, use “lmflash –h”. To see other examples of command lines, use “lmflash –examples”.~~	+

	==Optional USB Debug Port Unlock Procedure==		==Optional USB Debug Port Unlock Procedure==

Support at 13:22, 27 March 2012

Support — Tue, 27 Mar 2012 13:22:22 GMT

← Older revision		Revision as of 13:22, 27 March 2012
Line 76:		Line 76:

	==Compile a Code Example==		==Compile a Code Example==
-		+	{{:Compile Code Examples Eagle SBC}}
-	~~===Compiling Applications with EWARM===~~	+
-	To load the StellarisWare workspace in the IAR IDE, select Programs> Micromint Eagle> IAR> StellarisWare examples from the Windows Start menu. The IAR Embedded Workbench for ARM will start and you will see a screen similar to that in Figure 2.5. Select the Blinky project by clicking on the drop down menu circled red in Figure 2.5. Be sure to select the board that you are using. In the case of Figure 2.5 the Eagle 50E was being used. To rebuild the project select the “Make” button on the toolbar. You can also right click on the project name to select “Make” or “Rebuild”. This will build a binary (.BIN) image file in the “board type\ewarm\Exe\” directory of the project. For example the binary for the blinky project using the Eagle 50E is in the “C:\Program Files\Micromint\Eagle\StellarisWare\boards\eagle\blinky\eagle-50e\ewarm\Exe” directory if the Eagle BSP was installed in the default directory. To load the application on the board please see the Firmware Download Procedures section in this manual. If the build and download is successful, the user LED on the Eagle SBC ~~will start blinking.~~	+
-		+
-	~~[[Image:IAR_EWARM_IDE.png\|center\|frame\|alt=IAR EWARM IDE\|Figure 2.5: Using StellarisWare projects with the IAR EWARM IDE]]~~	+
-		+
-	~~===Compiling Applications with the GNU Toolchain===~~	+
-	~~====Compiling Applications with the CodeBlocks IDE====~~	+
-	To load the StellarisWare workspace in the CodeBlocks IDE, select Programs> Micromint Eagle> CodeBlocks> StrellarisEare examples from your Windows Start menu. The CodeBLocks IDE will start and you will see a screen similar to that on Figure 2.6. Select the Blinky project by right clicking the project name and selecting “Activate project”. Select the appropriate board using the dropdown menu circled red in figure 2.6. To rebuild the project select the “Rebuild” button on the toolbar. You can also right click on the project name to select “Build” or “Rebuild”. This will build a binary (.BIN) image file in the “board type\gcc\” directory of the project. For example the binary for the blinky project using the Eagle 50E is in the “C:\Program Files\Micromint\Eagle\StellarisWare\boards\eagle\blinky\eagle-50e\gcc” directory if the Eagle BSP was installed in the default directory. To load the application on the board please see the Firmware Download Procedures section in this manual. If the build and download is successful, the user LED on the Eagle SBC will start blinking.	+
-		+
-	~~[[Image:CodeBlocks_IDE.png\|center\|frame\|alt=CodeBlocks IDE\|Figure 2.6: Using the StellarisWare projects with the CodeBlocks IDE]]~~	+
-		+
-	~~====Compiling Applications with the Eclipse IDE====~~	+
-		+
-	~~====Compiling Applications with the GNU Toolchain from the Command Line====~~	+
-	All example programs include a Makefile that allows you to build binary images from the command line using the GNU toolchain. The GNU “make” utility is installed as part of the GNU toolchain on the Eagle Setup CD. To build an image using the command line, just change to the project directory and execute “make”. To build the image for blinky you would perform the following:	+
-	* 1. Open a command prompt.	+
-	* 2. Type “CD\Program Files\Micromint\Eagle\StellarisWare\boards\eagle\blinky”.	+
-	* 3. Press “Enter”.	+
-	* 4. Type “make”.	+
-	* 5. Press “Enter”.	+

	==Download the Code Example to the Eagle 50/50E==		==Download the Code Example to the Eagle 50/50E==

Support at 13:06, 27 March 2012

Support — Tue, 27 Mar 2012 13:06:49 GMT

← Older revision		Revision as of 13:06, 27 March 2012
Line 67:		Line 67:
	* 8. Type “?” then press enter for the command list.		* 8. Type “?” then press enter for the command list.

-	==Install ~~the~~ Eagle Code Examples==	+	{{:Install Eagle Code Examples}}
-	The Eagle Code Examples are generated from Stellarisware and may be downloaded from the Software Updates section of the [http://wiki.micromint.com/index.php/Eagle_Documentation Eagle Documentation Wiki]. After they are downloaded unzip them into a directory of your choice. Descriptions of the examples can be viewed on the [http://wiki.micromint.com/index.php/Eagle_Examples Eagle Examples Page].	+

	{{:Cortex M3 Compiler Installation}}		{{:Cortex M3 Compiler Installation}}