Bambino-200 Manual/Updating Firmware - Revision history

Support: /* Updating Firmware */

2013-09-03T18:30:21Z

Updating Firmware

← Older revision		Revision as of 18:30, 3 September 2013
Line 5:		Line 5:
	1. Install the DFU Flash Programmer to a directory in your hard disk. Currently the NXP DFU programmer is only available for Windows.		1. Install the DFU Flash Programmer to a directory in your hard disk. Currently the NXP DFU programmer is only available for Windows.

-	2. Place the board in USB boot mode by shorting the two contacts labelled "Boot JP1" as shown below while pressing and releasing the RESET button. Metal tweezers work great for shorting the two contacts. If you will be doing frequent updates, you may consider soldering a 2-pin header ~~on that position~~ and use a jumper to enter the USB boot mode.	+	2. Place the board in USB boot mode by shorting the two contacts labelled "Boot JP1" as shown below while pressing and releasing the RESET button. Metal tweezers work great for shorting the two contacts. If you will be doing frequent updates, you may consider soldering a 2-pin header in and use a jumper to enter the USB boot mode.

	[[Image:Bam200-JP1.png\|center\|alt=Boot Jumper (JP1)\|frame\|<div align="center">'''Boot Jumper]]</div>		[[Image:Bam200-JP1.png\|center\|alt=Boot Jumper (JP1)\|frame\|<div align="center">'''Boot Jumper]]</div>

Support: /* Updating Firmware */

2013-09-03T18:28:52Z

Updating Firmware

← Older revision		Revision as of 18:28, 3 September 2013
Line 5:		Line 5:
	1. Install the DFU Flash Programmer to a directory in your hard disk. Currently the NXP DFU programmer is only available for Windows.		1. Install the DFU Flash Programmer to a directory in your hard disk. Currently the NXP DFU programmer is only available for Windows.

-	2. Place the board in USB boot mode by ~~placing a jumper wire between~~ the two contacts labelled "Boot JP1" as shown below. If you will be doing frequent updates, you may consider soldering a 2-pin header on that position and use a jumper to enter the USB boot mode.	+	2. Place the board in USB boot mode by shorting the two contacts labelled "Boot JP1" as shown below while pressing and releasing the RESET button. Metal tweezers work great for shorting the two contacts. If you will be doing frequent updates, you may consider soldering a 2-pin header on that position and use a jumper to enter the USB boot mode.

	[[Image:Bam200-JP1.png\|center\|alt=Boot Jumper (JP1)\|frame\|<div align="center">'''Boot Jumper]]</div>		[[Image:Bam200-JP1.png\|center\|alt=Boot Jumper (JP1)\|frame\|<div align="center">'''Boot Jumper]]</div>

-	3~~. Press the RESET button~~. An entry "LPC USB" should appear in the Windows Device Manager. If your device is not recognized, please check that you have the [http://www.micromint.com/updates/bambino/bambino-drivers.zip USB Drivers] installed.	+	3. An entry "LPC USB" should appear in the Windows Device Manager. If your device is not recognized, please check that you have the [http://www.micromint.com/updates/bambino/bambino-drivers.zip USB Drivers] installed.

	[[Image:LPC-USB.png\|center\|alt=LPC USB Device\|frame\|<div align="center">'''LPC USB device]]</div>		[[Image:LPC-USB.png\|center\|alt=LPC USB Device\|frame\|<div align="center">'''LPC USB device]]</div>

Support at 19:04, 26 August 2013

2013-08-26T19:04:40Z

← Older revision		Revision as of 19:04, 26 August 2013
Line 9:		Line 9:
	[[Image:Bam200-JP1.png\|center\|alt=Boot Jumper (JP1)\|frame\|<div align="center">'''Boot Jumper]]</div>		[[Image:Bam200-JP1.png\|center\|alt=Boot Jumper (JP1)\|frame\|<div align="center">'''Boot Jumper]]</div>

-	3. Press the ~~reset~~ button. An entry "LPC USB" should ~~then~~ appear in the Windows Device Manager. If your device is not recognized, please check that you have the [http://www.micromint.com/updates/bambino/bambino-drivers.zip USB Drivers] installed.	+	3. Press the RESET button. An entry "LPC USB" should appear in the Windows Device Manager. If your device is not recognized, please check that you have the [http://www.micromint.com/updates/bambino/bambino-drivers.zip USB Drivers] installed.

	[[Image:LPC-USB.png\|center\|alt=LPC USB Device\|frame\|<div align="center">'''LPC USB device]]</div>		[[Image:LPC-USB.png\|center\|alt=LPC USB Device\|frame\|<div align="center">'''LPC USB device]]</div>

Support: /* Updating Firmware */

2013-08-26T19:03:33Z

Updating Firmware

← Older revision		Revision as of 19:03, 26 August 2013
Line 5:		Line 5:
	1. Install the DFU Flash Programmer to a directory in your hard disk. Currently the NXP DFU programmer is only available for Windows.		1. Install the DFU Flash Programmer to a directory in your hard disk. Currently the NXP DFU programmer is only available for Windows.

-	2. Place the board in USB boot mode by placing a jumper wire between the two contacts labelled "Boot JP1" ~~(Figure 4-1)~~. If you will be doing frequent updates, you may consider soldering a 2-pin header on that position and use a jumper to enter the USB boot mode.	+	2. Place the board in USB boot mode by placing a jumper wire between the two contacts labelled "Boot JP1" as shown below. If you will be doing frequent updates, you may consider soldering a 2-pin header on that position and use a jumper to enter the USB boot mode.

	[[Image:Bam200-JP1.png\|center\|alt=Boot Jumper (JP1)\|frame\|<div align="center">'''Boot Jumper]]</div>		[[Image:Bam200-JP1.png\|center\|alt=Boot Jumper (JP1)\|frame\|<div align="center">'''Boot Jumper]]</div>

-	3. Press the reset button. An entry "LPC USB" should then appear in the Windows Device Manager ~~(Figure 4-1)~~. If your device is not recognized, please check that you have the [http://www.micromint.com/updates/bambino/bambino-drivers.zip USB Drivers] installed.	+	3. Press the reset button. An entry "LPC USB" should then appear in the Windows Device Manager. If your device is not recognized, please check that you have the [http://www.micromint.com/updates/bambino/bambino-drivers.zip USB Drivers] installed.

	[[Image:LPC-USB.png\|center\|alt=LPC USB Device\|frame\|<div align="center">'''LPC USB device]]</div>		[[Image:LPC-USB.png\|center\|alt=LPC USB Device\|frame\|<div align="center">'''LPC USB device]]</div>

Support at 19:01, 26 August 2013

2013-08-26T19:01:49Z

← Older revision		Revision as of 19:01, 26 August 2013
Line 34:		Line 34:
	5. After the flash is complete, exit the utility, remove the boot jumper, and reset your board. You need to press RESET twice due to an issue documented in the [http://www.nxp.com/documents/errata_sheet/ES_LPC43X0.pdf LPC43X0 Errata] for boards booting from SPIFI flash.		5. After the flash is complete, exit the utility, remove the boot jumper, and reset your board. You need to press RESET twice due to an issue documented in the [http://www.nxp.com/documents/errata_sheet/ES_LPC43X0.pdf LPC43X0 Errata] for boards booting from SPIFI flash.

-	6. Three [http://www.micromint.com/updates/bambino/bambino-drivers.zip USB Drivers] are provided for the Bambino 200.	+	6. Three [http://www.micromint.com/updates/bambino/bambino-drivers.zip USB Drivers] are provided for the Bambino 200. Selecting the top directory allows Windows to select the appropriate one based on the vendor and product ID (VID/PID).

	{\| border="1" cellpadding="2" cellspacing="2" align="center"		{\| border="1" cellpadding="2" cellspacing="2" align="center"

Support: /* Updating Firmware */

2013-08-26T18:59:44Z

Updating Firmware

← Older revision		Revision as of 18:59, 26 August 2013
Line 17:		Line 17:
	[[Image:LPC-DFU.png\|center\|alt=LPC DFU Flash Programmer\|frame\|<div align="center">'''LPC DFU Flash Programmer]]</div>		[[Image:LPC-DFU.png\|center\|alt=LPC DFU Flash Programmer\|frame\|<div align="center">'''LPC DFU Flash Programmer]]</div>

-	5. Use the following parameters and press START. You may need to use full paths for the algorithm (.hdr) and firmware (.bin) files.	+	5. Use the following parameters and press START. You may need to use full paths for the algorithm (.hdr) and firmware (.bin) files. If you want to maintain deployed assemblies when updating TinyCLR, reduce the size to 0x070000 so the rest of the flash is not updated.

	Algorithm: .\Programming_algorithms\iram_dfu_util_spiflash.bin.hdr		Algorithm: .\Programming_algorithms\iram_dfu_util_spiflash.bin.hdr

Support at 18:55, 26 August 2013

2013-08-26T18:55:51Z

← Older revision		Revision as of 18:55, 26 August 2013
Line 44:		Line 44:
	\|-		\|-
	\|WinUSB		\|WinUSB
-	\|~~CDC~~	+	\|WinUSB\BambinoUSB.inf
-	~~\|DFU~~	+
-	\|-	+
-	\|	+
-	~~\|0x3720000~~	+
-	\|-	+
	\|Default NetMF driver		\|Default NetMF driver
		+	\|-
		+	\|CDC
		+	\|VCom\LpcVcom.inf
	\|Alternate NetMF driver		\|Alternate NetMF driver
		+	\|-
		+	\|DFU
		+	\|WinUSB\LpcDevice.inf
	\|Flash programmer		\|Flash programmer
	\|}		\|}

Support at 18:52, 26 August 2013

2013-08-26T18:52:51Z

← Older revision		Revision as of 18:52, 26 August 2013
Line 1:		Line 1:
	[[Category: Bambino-200_Manual\|04]]		[[Category: Bambino-200_Manual\|04]]
	==Updating Firmware==		==Updating Firmware==
-	The Bambino 200 firmwarte can be updated using the standalone [http://www.micromint.com/updates/bambino/dfusec.zip NXP DFU Flash Programmer]. This tool is ~~convenient for applications that need~~ to ~~install~~ firmware in ~~multiple~~ boards ~~to be deployed~~ in the field. It also allows developers to update the ~~bootloader and~~ firmware to a current version~~. NetMF applications can install the TinyBooter firmare from the SDK at '''C:\Program Files (x86)\Micromint\SDK\Bambino200\Firmware'''~~. Other applications can install their corresponding firmware using this flash programmer. To update firmware via DFU, please follow these steps:	+	The Bambino 200 firmwarte can be updated via the primary USB port using the standalone [http://www.micromint.com/updates/bambino/dfusec.zip NXP DFU Flash Programmer]. This tool is a simple alternative to update firmware in boards deplayed in the field. It also allows NetMF developers to update the [http://www.micromint.com/updates/bambino/200/TinyCLR-4.2.0.2.bin TinyCLR firmware] to a current version. Other applications can install their corresponding firmware using this flash programmer. To update firmware via DFU, please follow these steps:

	1. Install the DFU Flash Programmer to a directory in your hard disk. Currently the NXP DFU programmer is only available for Windows.		1. Install the DFU Flash Programmer to a directory in your hard disk. Currently the NXP DFU programmer is only available for Windows.
Line 9:		Line 9:
	[[Image:Bam200-JP1.png\|center\|alt=Boot Jumper (JP1)\|frame\|<div align="center">'''Boot Jumper]]</div>		[[Image:Bam200-JP1.png\|center\|alt=Boot Jumper (JP1)\|frame\|<div align="center">'''Boot Jumper]]</div>

-	3. Press the reset button. An entry "LPC USB" should then appear in the Windows Device Manager (Figure 4-1). If your device is not recognized, please check that you have the [http://~~wiki~~.micromint.com/~~index.php~~/~~Bambino_Documentation#Drivers~~ USB Drivers] installed.	+	3. Press the reset button. An entry "LPC USB" should then appear in the Windows Device Manager (Figure 4-1). If your device is not recognized, please check that you have the [http://www.micromint.com/updates/bambino/bambino-drivers.zip USB Drivers] installed.

	[[Image:LPC-USB.png\|center\|alt=LPC USB Device\|frame\|<div align="center">'''LPC USB device]]</div>		[[Image:LPC-USB.png\|center\|alt=LPC USB Device\|frame\|<div align="center">'''LPC USB device]]</div>
Line 28:		Line 28:
	No checkboxes neede		No checkboxes neede

-	You can test the procedure using ~~the the device with~~ the file listed below.	+	You can test the procedure using the file listed below.

	: .\Prebuilt_examples\bambino200\blinky_spifi_bambino_200.bin		: .\Prebuilt_examples\bambino200\blinky_spifi_bambino_200.bin

-	5. After the flash is complete, exit the utility, remove the boot jumper, and reset your board.	+	5. After the flash is complete, exit the utility, remove the boot jumper, and reset your board. You need to press RESET twice due to an issue documented in the [http://www.nxp.com/documents/errata_sheet/ES_LPC43X0.pdf LPC43X0 Errata] for boards booting from SPIFI flash.

-	~~==Updating the NetMF TinyCLR==~~	+	6. Three [http://www.micromint.com/updates/bambino/bambino-drivers.zip USB Drivers] are provided for the Bambino 200.
-	~~For NetMF development, after updating the TinyBooter firmware you can update the TinyCLR using the~~ [http://~~msdn~~.~~microsoft~~.com/~~en-us~~/~~library~~/~~ee435046~~.~~aspx Micro Framework Deployment Tool (MFDeploy)~~]~~. Go to 'Start', 'Programs', 'Microsoft .NET Micro Framework 4.2', 'Tools' and click on~~ the ~~MFDeploy entry. Select USB as the device type and~~ Bambino ~~200_Gadgeteer~~. ~~You should see a display similar to the one below:~~	+

-	~~[[Image:Bam200-MFDeploy.png~~\|~~center\|alt~~=~~MF Deploy\|frame\|<div~~ align="center"~~>'''MF Deploy]]</div>~~	+	{\| border="1" cellpadding="2" cellspacing="2" align="center"
		+	\|+ align="bottom"\|USB Drivers
		+	\|-
		+	!Driver
		+	!Directory
		+	!Purpose
		+	\|-
		+	\|WinUSB
		+	\|CDC
		+	\|DFU
		+	\|-
		+	\|
		+	\|0x3720000
		+	\|-
		+	\|Default NetMF driver
		+	\|Alternate NetMF driver
		+	\|Flash programmer
		+	\|}

-	Go to the image file field, click 'Browse' and select the firmware files on ''''C:\Program Files (x86)\Micromint\SDK\Bambino200\Firmware'''. Select config.hex and firmware.hex, click 'Deploy' to update the TinyCLR on your board.
	----		----
	[[Bambino-200_Manual/Rebuild Firmware\|NEXT: Rebuild NetMF Firmware]]		[[Bambino-200_Manual/Rebuild Firmware\|NEXT: Rebuild NetMF Firmware]]

	[[Bambino-200_Manual/Getting Started mbed\|PREVIOUS: Getting Started - mbed Applications]]		[[Bambino-200_Manual/Getting Started mbed\|PREVIOUS: Getting Started - mbed Applications]]

Support at 11:23, 11 July 2013

2013-07-11T11:23:37Z

← Older revision		Revision as of 11:23, 11 July 2013
Line 1:		Line 1:
-	[[Category: Bambino-200_Manual\|4]]	+	[[Category: Bambino-200_Manual\|04]]
	==Updating Firmware==		==Updating Firmware==
	The Bambino 200 firmwarte can be updated using the standalone [http://www.micromint.com/updates/bambino/dfusec.zip NXP DFU Flash Programmer]. This tool is convenient for applications that need to install firmware in multiple boards to be deployed in the field. It also allows developers to update the bootloader and firmware to a current version. NetMF applications can install the TinyBooter firmare from the SDK at '''C:\Program Files (x86)\Micromint\SDK\Bambino200\Firmware'''. Other applications can install their corresponding firmware using this flash programmer. To update firmware via DFU, please follow these steps:		The Bambino 200 firmwarte can be updated using the standalone [http://www.micromint.com/updates/bambino/dfusec.zip NXP DFU Flash Programmer]. This tool is convenient for applications that need to install firmware in multiple boards to be deployed in the field. It also allows developers to update the bootloader and firmware to a current version. NetMF applications can install the TinyBooter firmare from the SDK at '''C:\Program Files (x86)\Micromint\SDK\Bambino200\Firmware'''. Other applications can install their corresponding firmware using this flash programmer. To update firmware via DFU, please follow these steps:

Support at 13:30, 8 July 2013

2013-07-08T13:30:22Z

← Older revision		Revision as of 13:30, 8 July 2013
Line 41:		Line 41:
	Go to the image file field, click 'Browse' and select the firmware files on ''''C:\Program Files (x86)\Micromint\SDK\Bambino200\Firmware'''. Select config.hex and firmware.hex, click 'Deploy' to update the TinyCLR on your board.		Go to the image file field, click 'Browse' and select the firmware files on ''''C:\Program Files (x86)\Micromint\SDK\Bambino200\Firmware'''. Select config.hex and firmware.hex, click 'Deploy' to update the TinyCLR on your board.
	----		----
-	[[Bambino-200_Manual/Rebuild Firmware\|NEXT: Rebuild Firmware]]	+	[[Bambino-200_Manual/Rebuild Firmware\|NEXT: Rebuild NetMF Firmware]]

	[[Bambino-200_Manual/Getting Started mbed\|PREVIOUS: Getting Started - mbed Applications]]		[[Bambino-200_Manual/Getting Started mbed\|PREVIOUS: Getting Started - mbed Applications]]